| Z6200 |
01.0:10 |
Main PCA hardware failure |
Turn off/on. Replace Main PCA |
| Z6200 |
01.1:10 |
PrintMech PCA hardware failure |
Turn off/on. Replace PrintMech PCA |
| Z6200 |
01.2:10 |
ISS Top PCA communication failure |
Turn off/on. Replace Ink Suppy Tubes and Trailing Cable |
| Z6200 |
01.3:10 |
ISS Bottom PCA communication failure |
Turn off/on. Replace the Ink Supply Tubes and Trailing Cable. |
| Z6200 |
02.1:10 |
Carriage PCA Communication failure |
Turn off/on. Check trailing cable, check cable connection to PCA, Replace Carriage PCA |
| Z6200 |
03:10 |
Power Distibution failure |
Turn off/on. If power Supply inits blue LED is on, replace the PrintMech PCA, if not replace power supply |
| Z6200 |
05:10 |
Formatter communication failure with ISS |
Turn off/on. Check cable from formatter to PrintMech PCA. Replace Formatter |
| Z6200 |
06:03 |
Main NVM communication failure |
Turn off/on. If the System Error continues, replace the Hard Disk Drive |
| Z6200 |
08:11 |
Front Panel communication failure |
Turn off/on. If no display The Power Switch and Formatter LEDs can help you to troubleshoot, HP Authorized tech required |
| Z6200 |
11:10 |
Trailing Cable does not seem to be connected |
Check the trailing cable, check connection to Carriage PCA, Interconnect PCA and Main PCA, replace Ink supply Tibes and trailing cable |
| Z6200 |
17.0:11 |
PrintMech to Interconnect Power cable not connected |
Check cable for damage, check printmech interconnect power cable connections, replace the PrinMech to Inerconnect power cable |
| Z6200 |
17.2:11 |
PrintMech to Interconnect Data 2 cable not connected |
Check cable for damage, check printmech interconnect Data 2 connections, Replace the PrintMech to Interconnect Data 2 cable |
| Z6200 |
17.4:11 |
Main PCA to PrintMech Blue 2 cable not connected |
Check that the Main PCA to PrintMech Blue 2 cable for damage anc connectivity, replace cable |
| Z6200 |
21:03 |
Service Station electrical current limit |
Turn off/on. Check Service station path for obstacles, If error continues replace the Service Station |
| Z6200 |
21:13 |
Service station jam |
Turn off/on. Check Service station path for obstacles, If error continues replace the Service Station |
| Z6200 |
23:10 |
Air Pressurization System failure |
Turn off/on. Check the APS cable connection to PCA, check air tubes are connected and not pinched, repalce APS Assembly |
| Z6200 |
24:03 |
Ink Supply Tubes purge failure |
Turn off/on. Ensure that the dummy printheads are correctly installed and purge the Ink Supply Tubes again, replace Setup Pritnhead kit |
| Z6200 |
24:10 |
Broken Bad detected in one ink cartridge |
Press Down + Cancel to see which cartridge, remove cartridge, check if air tower is contaminated with ink, if contaminated replace ink supply tubes and trailing cable |
| Z6200 |
24:11 |
PrintMech to ISS Top cable does not seem to be connected |
Check PrintMech to ISS Top cable, Check PrinMech to ISS top cable is connected to PrintMech PCA and ISS Top PCA, repalce PrintMech to ISS Top Cable |
| Z6200 |
24.1:11 |
ISS Top to ISS Bottom cable does not seem to be connected |
Check ISS Top to ISS Bottom Cable for damage and connectivity, replace the ISS Top to ISS Bottom Cable |
| Z6200 |
26:01 |
Bad contact detected in ISS slot 0 floater |
Remove Magent Ink and reinstall, Replace magenta ink, check that the ISS to cartridge cable is not damaged and is correctly connected to Ink Supply, Replace cable |
| Z6200 |
26.1:01 |
Bad contact detected in ISS slot 1 floater |
Remove Lt Magent Ink and reinstall, Replace Lt Magenta ink, check that the ISS to cartridge cable is not damaged and is correctly connected to Ink Supply, Replace cable |
| Z6200 |
26.2:01 |
Bad contact detected in ISS slot 2 floater |
Remove Photo black Ink and reinstall, Replace PK ink, check that the ISS to cartridge cable is not damaged and is correctly connected to Ink Supply, Replace cable |
| Z6200 |
26.3:01 |
Bad contact detected in ISS slot 3 floater |
Remove Matte black Ink and reinstall, Replace Matte Black ink, check that the ISS to cartridge cable is not damaged and is correctly connected to Ink Supply, Replace cable |
| Z6200 |
26.4:01 |
Bad contact detected in ISS slot 4 floater |
Remove Yellow Ink and reinstall, Replace Yellow ink, check that the ISS to cartridge cable is not damaged and is correctly connected to Ink Supply, Replace cable |
| Z6200 |
26.5:01 |
Bad contact detected in ISS slot 5 floater |
Remove light Cyan Ink and reinstall, Replace Light Cyan ink, check that the ISS to cartridge cable is not damaged and is correctly connected to Ink Supply, Replace cable |
| Z6200 |
26.6:01 |
Bad contact detected in ISS slot 6 floater |
Remove light Gray Ink and reinstall, Replace Light Gray ink, check that the ISS to cartridge cable is not damaged and is correctly connected to Ink Supply, Replace cable |
| Z6200 |
26.7:01 |
Bad contact detected in ISS slot 7 floater |
Remove Red Ink and reinstall, Replace red ink, check that the ISS to cartridge cable is not damaged and is correctly connected to Ink Supply, Replace cable |
| Z6200 |
27.1:01 |
Calibration failed poor Magenta/Yellow Printhead in slot 1 |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status, Replace Printhead |
| Z6200 |
27.2:01 |
Calibration failed poor Magenta/Yellow Printhead in slot 2 |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status, Replace Printhead |
| Z6200 |
27.3:01 |
Calibration failed poor performance of the Lt Cyan/Lt Magenta |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status, Replace Printhead |
| Z6200 |
27.4:01 |
Calibration failed poor performance of the Lt Cyan/Lt Magenta |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
27.5:01 |
Calibration failed poor performance of the PK/LT Gray Slot 5 |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
27.6:01 |
Calibration failed poor performance of the PK/LT Gray Slot 6 |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
27.7:01 |
Calibration failed poor performance of the MK/Red Gray Slot 7 |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
27.8:01 |
Calibration failed poor performance of the MK/Red Gray Slot 8 |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.1:01 |
Magenta/Yellow Printhead in slot 1 is deteriorating |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.2:01 |
Magenta/Yellow Printhead in slot 2 is deteriorating |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.3:01 |
Light Cyan/Light Magenta Printhead in slot 3 is deteriorating |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.4:01 |
Light Cyan/Light Magenta Printhead in slot 3 is deteriorating |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.5:01 |
Photo Black/Light Gray Printhead in slot 5 is deteriorating |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.6:01 |
Photo Black/Light Gray Printhead in slot 6 is deteriorating |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.7:01 |
Matte Black/Red Printhead in slot 7 is deteriorating |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.8:01 |
Matte Black/Red Printhead in slot 8 is deteriorating |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.1:02 |
Magenta/Yellow Printhead in slot 1 is at end of useful life |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.2:02 |
Magenta/Yellow Printhead in slot 2 is at end of useful life |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.3:02 |
Light Cyan/Light Magenta Printhead in slot 3 is at end of useful life |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.4:02 |
Light Cyan/Light Magenta Printhead in slot 3 is at end of useful life |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.5:02 |
Photo Black/Light Gray Printhead in slot 5 is at end of useful life |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.6:02 |
Photo Black/Light Gray Printhead in slot 6 is at end of useful life |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.7:02 |
Matte Black/Red Printhead in slot 7 is at end of useful life |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
28.8:02 |
Matte Black/Red Printhead in slot 8 is at end of useful life |
This may impact your print quality. If it becomes unacceptable in the future, clean all printheads and check their status., Replace Printhead |
| Z6200 |
29:00 |
Maintenance Cartridge almost full |
Replace the Maintenance Cartridge. |
| Z6200 |
29:01 |
Maintenance Cartridge not inserted correctly |
Open the Maintenance Cartridge door on the right-hand side of the printer, make sure that the maintenance cartridge is correctly seated, then close the door. Replace Cartridge |
| Z6200 |
29:02 |
Ink Absorber almost full |
Replace the Ink Absorber. |
| Z6200 |
32:01 |
Take-up Reel (TUR) communication failure |
Turn off the printer and check that all TUR cables are connected (sensor cables, printer cable). Remember to Cut paper Manually Form Feed and Cut key. |
| Z6200 |
32:01.2 |
Take-up Reel (TUR) paper jam |
Check that there is no interference around the TUR optical sensors, Check paper attachment, check TUR switch position, Check for obstacles, Rewind paper, check sensors. |
| Z6200 |
32:01.9 |
Take-up Reel (TUR) disabled because paper was removed |
Remove all paper from the printer and reinstall the TUR. |
| Z6200 |
32:02 |
Take-up Reel not detected or disconnected when printer off |
Connect the TUR to the printer and press OK to continue. |
| Z6200 |
36.0:01 |
Duplexer communication error |
Reseat the cables between the Duplexer and the printer, Uninstall and reinstall the Duplexer, contact the manufacturer of the Duplexer. |
| Z6200 |
36.01:01 |
Duplexer paper incorrect lateral edge position |
Unload the paper and try again,contact the manufacturer of the Duplexer. |
| Z6200 |
36.03:01 |
Duplexer unable to detect paper |
Unload the paper and try again, contact the manufacturer of the Duplexer. |
| Z6200 |
36.1:01 |
Duplexer not ready for printing |
The Duplexer was in the down position when the job was submitted |
| Z6200 |
36.2:01 |
Duplexer internal error |
Reseat the cables between the Duplexer and the printer, Uninstall and reinstall the Duplexer, contact the manufacturer of the Duplexer. |
| Z6200 |
41:03 |
Paper motor electrical current limit |
Turn the power off at the rear of the printer and disconnect the power cord, check & remove for obstacles, Replace the Media-Axis Motor |
| Z6200 |
42:03 |
Scan-Axis motor electrical current limit |
Turn off/on. Check for visible obstacles. Clean the encoder Strip, repalce the Scan-Axis motor |
| Z6200 |
43:01 |
Vacuum Fan spinning at wrong speed |
Turn off/on. If the system error persists, replace the Vacuum Fan |
| Z6200 |
43:10 |
Vacuum Fan failure |
Turn off/on. Check that the Vacuum Fan cable, Check that the Interconnect to Vacuum Driver cable, Replace the Vacuum Fan |
| Z6200 |
43.1:10 |
Vacuum Driver PCA communication or hardware failure |
Turn off/on. If the system error persists, replace the Vacuum Fan |
| Z6200 |
43:11 |
Vacuum Fan PCA cable does not seem to be connected |
Check that the Interconnect PCA to Vacuum Driver cable and PCA to Vacuum Driver cable. replace the Interconnect PCA to Vacuum Driver cable. |
| Z6200 |
44.1:10 |
Left Aerosol Fan stopped |
Turn off/on. Check connection Left Aerosol Fan cable to PrintMech PCA. Check any obstacle blocking the fan, Replace the Left Aerosol Fan. |
| Z6200 |
44.2:10 |
Right Aerosol Fan stopped or spinning at lower speed |
Turn off/on. Check connection Right Aerosol Fan cable to PrintMech PCA. Check any obstacle blocking the fan, Replace the Right Aerosol Fan. |
| Z6200 |
44.4:10 |
Right Aerosol Fan Filter blocked |
Turn off/on. Check that the Right Aerosol Fan cable is not damaged and connected to PrintMech PCA, replace the Aerosol Filter. |
| Z6200 |
45:03 |
Rewinder servo shutdown |
Turn off/on. Check for visible obstacles restricting the movement of the Drive Roller, lift Pinch Wheels & clear, Replace the Rewinder Motor. |
| Z6200 |
46:03 |
Primer servo shutdown |
Check that the Primer Arm, Turn off/on, Replace the Primer Assembly |
| Z6200 |
46:13 |
Primer test distance failed |
Check that the Primer Arm, Turn off/on, Replace the Primer Assembly |
| Z6200 |
50:03 |
OMAS fatal error or disconnected |
Turn off/on. Check Power Supply to OMAS Controller cable, Replace the OMAS Controller Card |
| Z6200 |
50.1:10 |
OMAS Module communication failure |
Turn off/on. Check that the OMAS Controller to OMAS Sensor cable. Replace the OMAS Module |
| Z6200 |
50:14 |
Firmware version mismatch OMAS and Hard Disk Drive |
Turn off/on. Check that the printer has the latest firmware version, Replace the OMAS Controller Card |
| Z6200 |
50.2:10 |
OMAS Controller Card communication failure |
Turn off/on. Check that the printer has the latest firmware version, Replace the OMAS Controller Card |
| Z6200 |
50.3:11 |
Main PCA to OMAS Controller cable is not connected |
Check that the Main PCA to OMAS Controller cable, Check that the Main PCA to OMAS Controller cable is connected to the Main PCA and the OMAS Controller Card. |
| Z6200 |
51:10 |
Error detected in the Window Position Sensor |
Check that the Window Position Sensor cable ok and connected to the Interconnect PCA, Replace the Window Position Sensor |
| Z6200 |
51.1:10 |
Error detected in the Maintenance Cartridge Door Sensor |
Check sensor cable, Replace the Maintenance Cartridge Door Sensor |
| Z6200 |
52:10 |
Drop Detector switch On/Off failure |
Turn off/on. Check e Drop Detector cable OK and connected to Service Station. Check SS cable connected to Interconnect PCA, Replace drop detector |
| Z6200 |
53:10 |
Media Sensor error |
Check that the Media Sensor cable is not damaged and connect to interconnect PCA, Replace the Media Sensor |
| Z6200 |
53.1:11 |
Media Sensor cable does not seem to be connected |
Check that the Media Sensor cable is not damaged, Check Media Sensor cable is correctly connected to the Interconnect PCA |
| Z6200 |
54:10 |
Media Lever Sensor error |
Check Media Lever Sensor cable, Replace the Media Lever Sensor |
| Z6200 |
55:10 |
Line Sensor communication failure |
Turn off/on. Replace the Line Sensor |
| Z6200 |
56:01 |
Incorrect readings from paper encoder |
Turn off/on. Perform Paper Drive diagnostics, Replace the Encoder Disc and Sensor |
| Z6200 |
58:01 |
Embedded PhotoSpectrometer (ESP) shutter error |
Execute the ESP Shutter Diagnostic Test. |
| Z6200 |
58:10 |
Embedded PhotoSpectrometer (ESP) failure |
Turn off/on. Check that the ESP is installed in the: Carriage, screwed into place,connected to the Carriage PCA.if error persists, replace the ESP, test ESP basic test CLC |
| Z6200 |
58.1:10 |
Embedded PhotoSpectrometer (ESP) Shutter Actuator failure |
Replace the ESP Shutter Actuator Assembly,Perform the ESP Shutter Diagnostic Test, Perform am ESP basic test (CLC) |
| Z6200 |
58.2:10 |
Embedded PhotoSpectrometer (ESP) Shutter Deactivator failure |
Check that the Shutter Deactivator is correctly screwed into place, Replace the Left Spittoon Assembly, Perform the ESP Shutter Diagnostic Test and ESP basic test |
| Z6200 |
59.1:09 |
Two electrical parts have been replaced at the same time |
Replace one part at a time, and restart the printer before replacing another. |
| Z6200 |
59.2:00 |
An unsupported or reused part has been installed |
Install only new parts recommended by HP for this printer. |
| Z6200 |
60.1:11 |
Initialization error |
Turn off/on. Check that the printer is properly connected in all other respects. |
| Z6200 |
60.2:17 |
Initialization error |
Contact HP Authorized Technician |
| Z6200 |
61:01 |
The file format is incorrect , printer cannot process the job |
Check the graphic language setting of the printer |
| Z6200 |
61:04.1 |
The PostScript fonts are missing |
Perform a full firmware update. |
| Z6200 |
61:04.2 |
PostScript unknown Paper ID |
Perform a full firmware update. |
| Z6200 |
61:08 |
The paper type specified in the file is incorrect |
Turn off/on. Change the paper type and resend the file to the printer. |
| Z6200 |
61:08.1 |
The file cannot be printed because it is password-protected |
Resend the file without password protection. |
| Z6200 |
61:08.2 |
The file contains format errors or incorrect settings |
Ensure that the file format sent is supported by the printer, Turn off/on. Resend the file to the printer using the Embedded Web Server. |
| Z6200 |
61:10 |
low computer processing complex files can timeout |
Increase the I/O timeout using the printer's front panel, Send the job from a faster computer, Send the job from the Embedded Web Server. |
| Z6200 |
64.1:01 |
Printer does not recognize the USB Hard Disk Drive accessory |
Turn off/on. Connect the Hard Disk Drive accessory, check that the USB cable ,Turn on while pressing Menu, OK and Cancel, press OK 2x, Error persist replace Formatter |
| Z6200 |
71:03 |
Out of memory failure |
Turn off/on, decrease file size to 300dpi, select Economode, Send job as a bitpmap |
| Z6200 |
71:08 |
Insufficient display list |
Resend, decrease resolution to 300 dpi, select Economode print mode, select Send Job As Bitmap |
| Z6200 |
74:01 |
Error uploading firmware update file |
Turn off/on. Resend file to printer. |
| Z6200 |
75.21:10 |
Total printer ink consumption reached upper limit |
This is a continuable system error, Service Station has ink build-up, best to replace service station |
| Z6200 |
76:03 |
Hard Disk Drive out of space |
Turn off/on. Resend the file, remove any unnecessary files from hard disk drive. Perform Hard Disk Recovery. |
| Z6200 |
77:04 |
Embedded Web Server internal software error |
Turn off/on. Check that the printer has the latest firmware version, update if needed. |
| Z6200 |
78.1:04 |
Media Settings area missing in media settings file |
Resend the file. |
| Z6200 |
79:03 |
Generic firmware error |
Turn off/onCheck that the printer has the latest firmware version, update if needed, perform Hard Disk Recovery |
| Z6200 |
79.2:04 |
Operating-system signal error |
Turn off/on. Check for latest firmware version, reprint the image using different selections, Disable nesting and the queue, perform Hard Disk Recovery |
| Z6200 |
81:01 |
Paper servo shutdown; possible paper jam |
Check for visible obstacles restricting the movement of the driver roller, check OMAS to PCA Cable, Check OMAS to PrintMech PCA, Perform Media drive Diagnostic |
| Z6200 |
85:03 |
Problem finding the Drive Roller zero |
Perform the Media Drive Diagnostic |
| Z6200 |
86:01 |
Carriage servo shutdown; possible paper jam |
Check for visible obstacles restricting the movement of the Carriage, lift the Pinchwheels and clear the obstruction, Perform the Scan-Axis Diagnostic |
| Z6200 |
86:11 |
Scan-Axis length requires too much force or energy |
Check that cutter disengages correctly,Check that cutter disengages correctly, Apply Preventive Maintenance Kit 1. |
| Z6200 |
87:01 |
Problem with the Scan Axis encoder sensor readings |
Encoder Strip is dirty, broken or damaged. Clean or replace the Encoder Strip, replace the Encoder Sensor, Perform the Scan Axis diagnostic test |
| Z6200 |
87:10 |
Problem with the Carriage Encoder Sensor readings |
Check that the Encoder Sensor is correctly connected to the Carriage PCA, clean the Encoder Sensor, replace the Encoder Sensor. |
| Z6200 |
94:01 |
The paper is not suitable for color calibration |
If accurate color is important, change to a different paper type |
| Z6200 |
94:02 |
Color calibration error: |
check if paper type selected corresponded to the paper actually loaded, Inspect the CLC printed target to detect banding, etc. fun Printing IQ full calibration, Use HP paper |
| Z6200 |
94:10 |
Embedded SpectroPhotometer (ESP) contaminated by aerosol |
Replace the ESP, Perform the ESP basic test (CLC) to ensure that the replaced part is working correctly. |